Home
Forums
New posts
What's new
New posts
Latest activity
Members
Registered members
Current visitors
Birthday calendar
Donate
Products
Calendar
Log in
Register
What's new
Registered members
Current visitors
Birthday calendar
Menu
Log in
Register
Install the app
Install
Home
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
409Steve62
Active Member
·
41
·
From
New Zealand
Joined
Sep 9, 2023
Last seen
Mar 8, 2024
Messages
41
Reaction score
50
Points
18
Latest activity
Postings
About
409Steve62
reacted to
La Hot Rods's post
in the thread
Carter 3361 3362 questions
with
Like
.
On the jet's, take a screwdriver that is bigger than the jet slots and grind it to fit proper in the jet slot. Then take a small hammer...
Feb 8, 2024
409Steve62
reacted to
dakota tom's post
in the thread
Carter 3361 3362 questions
with
Like
.
I would be looking for 3.70s with that cam.
Feb 7, 2024
409Steve62
replied to the thread
Carter 3361 3362 questions
.
Hey 32 Sorry about the late reply, different time zone and busy day at work. Yes the carbs are set up 1:1 , it’s very hard here to get...
Feb 7, 2024
409Steve62
reacted to
32witha409's post
in the thread
Carter 3361 3362 questions
with
Like
.
Steve, are you running your Edelbrocks progressive or synchronized. So, your cam, the high rear gear (3.08), and running the carbs...
Feb 7, 2024
409Steve62
reacted to
dakota tom's post
in the thread
Carter 3361 3362 questions
with
Like
.
Tip diameter.
Feb 6, 2024
409Steve62
replied to the thread
Carter 3361 3362 questions
.
Regarding the rods on both carbs in this post .057 seems to be the length or power? Is there different diameter measurements or is that...
Feb 6, 2024
409Steve62
reacted to
425/409ER's post
in the thread
Carter 3361 3362 questions
with
Like
.
I have 2 Eddy Thunder 500's on out 409 and it run great. Having the air valve in both carburetors is way better then the old Carter/Eddy...
Feb 6, 2024
409Steve62
reacted to
dakota tom's post
in the thread
Carter 3361 3362 questions
with
Like
.
I googled "409 chevy carb cfm rating" . In the results the web site " forabodiesonly.com" came up. Listed many carbs there. I haven't...
Feb 6, 2024
409Steve62
replied to the thread
Carter 3361 3362 questions
.
http://www.348-409.com/forum/threads/3361-3362-cfm.2823/ Here’s the link where I read that info, quite a few years ago this discussion...
Feb 6, 2024
409Steve62
reacted to
dakota tom's post
in the thread
Carter 3361 3362 questions
with
Like
.
The z33 cam is the same duration and close lift to the late 64-65 425 hp and z11 cam. A few degrees less lobe separation.
Feb 6, 2024
409Steve62
replied to the thread
Carter 3361 3362 questions
.
Thanks Tom this is a great starting point for me , let the fun begin. I’m running stock manifold & my z33 cam I measured a 53.5 lift...
Feb 6, 2024
409Steve62
replied to the thread
Carter 3361 3362 questions
.
I also thought the same but reading a lot of threads on this page and a lot of discussions have been had and the verdict seems to be...
Feb 6, 2024
409Steve62
reacted to
427John's post
in the thread
Carter 3361 3362 questions
with
Like
.
I think he was referring to the Edelbrock carbs being 500 cfm, Carter used to make a 500 cfm carb for dual quad apps but that was in the...
Feb 6, 2024
409Steve62
reacted to
dakota tom's post
in the thread
Carter 3361 3362 questions
with
Like
.
There was a post in a Facebook group of an old Bill Jenkins Q&A from a magazine. I saved it but I can't load it to this site. It showed...
Feb 6, 2024
409Steve62
reacted to
dakota tom's post
in the thread
Carter 3361 3362 questions
with
Like
.
I found a listing that showed 680 cfm for the 409 carbs.
Feb 6, 2024
Loading…
Loading…
Home
Members
Top